我们在使用燃气热风炉时清洁保养很重要

时间:2019年02月08日信息来源:环亚ag88 点击:次 收藏此文】 【字体:

我们在使用燃气环亚ag88时首先打开燃烧机门,拆下后部外壳面板,拧开环亚ag88后侧清洁口的螺丝。用钢丝刷清洁燃气管道。用软毛刷清洁燃烧室。燃气环亚ag88清除环亚ag88内的残渣,拧上清洁口的螺丝,关上燃烧机门,检查密封圈是否完整。如果环亚ag88安装在温度低于0℃的地区,必须采取以下防护措施:如果热风炉房在室外,将室内温度降到15℃或18℃,使热风炉整天运行。如果房间内长时间无人,应将热风炉内的水排空。
When we use the gas hot blast stove, we first open the burner door, remove the rear shell panel, and unscrew the screw of the cleaning opening on the back side of the hot blast stove. Clean gas pipeline with wire brush. Clean the combustion chamber with a soft brush. The gas hot blast stove removes the residue in the hot blast stove, screws the cleaning opening, closes the burner door, and checks whether the sealing ring is complete. If the hot-blast stove is installed in the area where the temperature is below 0 C, the following protective measures must be taken: if the hot-blast stove room is outside, the indoor temperature will be reduced to 15 C or 18 C, so that the hot-blast stove can run all day. If there is no one in the room for a long time, the water in the hot stove should be emptied. 阴极?;つ阒廊确缏母鞑考怯刹煌闹使钩?比如铸铁、铜、铝等)。为了防止电化学腐蚀,必须采取阴极?;ご胧?。热风炉的排污处理。环亚ag88底部排污可以防止烟气凝结。烟气凝结是由于烟气(柴油或天然气)中含水及烟气温度过低,有水份产生。这些水分一部分从烟囱排出,一部分被烟囱壁吸收,剩下的则沉积在烟囱底部。产生的水量受以下因素影响:烟气温度(效率达91%,烟气温度需达170℃)烟囱的总表面积,烟囱的材质及烟囱的保温情况。燃烧器的维修。燃气热风炉及燃烧器的维修,最好供汽后进行维修。因为燃烧产物会腐蚀热风炉,清理积碳,因此不可让燃烧产物在热风炉内存留时间过长。
Cathodic protection You know that hot stove components are made of different materials (such as cast iron, copper, aluminum, etc.). In order to prevent electrochemical corrosion, cathodic protection measures must be taken. Discharge treatment of hot blast stove. Gas hot blast stove bottom drainage can prevent smoke condensation. The condensation of flue gas is due to the moisture content in the flue gas (diesel or natural gas) and the low temperature of the flue gas, resulting in moisture. Some of the water is discharged from the chimney, some is absorbed by the chimney wall, and the rest is deposited at the bottom of the chimney. The amount of water produced is affected by the following factors: flue gas temperature (efficiency 91%, flue gas temperature needs to reach 170 C), the total surface area of the chimney, the material of the chimney and the temperature insulation of the chimney. Maintenance of burners. Maintenance of gas hot-blast stove and burner should be carried out after steam supply. Because the combustion products will corrode the hot blast stove and clean up the carbon deposit, the combustion products should not be allowed to stay in the hot blast stove for too long.

(作者:环亚ag88 编辑:admin)
文章热词:热风炉

热门文章

推荐文章